Char-lynn Torque Generator Universal Joint 7/8 Keyway To 5/8-36 Spline Steering Shaft Or Rack
Estimate Shipping
Price: $84.99
3 In Stock
Sold As:
1 Universal Joint
Part Number: SWT0732
MFG Number:
401-50732
California Prop 65 Warning: This item may cause cancer or reproductive harm. For more info visit p65warnings.ca.gov
Description
Charlynn Torque Generator steering universal joint. For added strength you can use a 5/16 x 2 inch bolt through the u-joint in addition to the half moon key.
This u joint will connect directly to a 5/8-36 spline steering shaft or allow you to connect your Charlynn directly up against the rack and pinion.
This u joint will connect directly to a 5/8-36 spline steering shaft or allow you to connect your Charlynn directly up against the rack and pinion.
Max Operating Angle: 30 Degrees
Material Type: Steel
Finish: Black Oxide
End #07: 5/8" 36 Spline With Set Screw 0.620 Major Diameter
End #32: 7/8" Smooth Bore With Keyway
If you're trying to replace one of Sweet Mfg's u-joints and haven't removed it from the car/truck/vehicle yet, you can turn the steering column to see the part number engraved on both sides of the universal joint.
Each end of the u-joint will have a part number engraved in it. Below is a complete list of Sweet Mfg's part numbers. For example if one end of the u-joint says 06 and the other end says 10 then that u-joint is 3/4 smooth weld on to 3/4 forty eight spline. We stock every common combination of Sweet Mfg's universal joints. If there are specific ends that you need on both sides of the universal joint, we can special order it from Sweet for you, but there's usually a 4 week wait and special order universal joints are not refundable.
Related Parts
Replacement 3/16" Woodruff Key For Eaton Char-Lynn 217-1015-002 Torque Generators
In Stock
Price: $1.69
Char-Lynn Torque Generator Donut Bracket For 3/4 Steering Shaft Sold individually
In Stock
Price: $6.99
Char-lynn Torque Generator Universal Joint 7/8 Keyway To 3/4 Smooth Steering Shaft
In Stock
Price: $79.99
Sweet Mfg Part Numbers:
1" Double D Note: OEM GM columns measure slightly less than 1" while I DIDIT and Flaming River aftermarket steering columns measure a true 1". DO NOT interchange these u-joints.- 06 = 3/4" Smooth Bore Weld On
- 07 = 5/8" 36 Spline 0.620 Major Diameter Stiletto Legend Car
- 08 = 5/8" Smooth Bore Weld On
- 09 = 1994 and Later Ford
- 10 = 3/4" 48 Spline
- 11 = 13/16" 36 Spline Chevy Power And Sweet Steering Box
- 12 = 3/4" 36 Spline Chevy Manual Steering And Ford Pinto Power
- 13 = 9/16" 26 Spline Ford Pinto Manual
- 14 = 5/8" 36 Spline 0.600 Major Diameter Chevy Vega
- 15 = 3/4" 30 Spline New Chevy Power Or Sweet INT Rack
- 17 = Chevy Corvette Top Set Screw
- 17 = Chevy Corvette Bottom Set Screw
- 18 = 1" 48 Spline Stock GM
- 19 = 3/4" Double D
- 20 = 1" Double D OEM GM Steering Column
- 21 = 3/4" 20 Spline Sweet Steering Column And Woodward Rack
- 23 = 1" Double D - Aftermarket I DIDIT Or Flaming River Steering Column
- 24 = Jeep 3D Flats
- 30 = 5/8" 36 Spline 0.605 Major Diameter Flaming River And Chevy Vega
- 32 = 7/8" Smooth Bore With Keyway For Charlynn
- 34 = 19/32" 29 Spline For Yamaha Rhino
- 35 = 15mm for VW and Mendeola Hockey Shifter With Set Screw
- 36 = 1/2" Smooth Bore
- 37 = 11/16" 36 Spline Toyota (17mm for our Electric Power Steering Units)
- 74 = Jeep Pincher