	Part Number & Description	Qty	Price
		Total

Kartek Offroad 1.5:1 Ratio Rack And Pinion With 5-7/8" Bump Steer Bracket For Extreme Performance

Note: Our FSBRACKHD and FSBRACKHDP racks are the same rack, just without the 5-7/8" bump steer bracket. If you're just doing a replacement on a rack and your pre-existing bump steer bracket is still good, you can use the FSBRACKHD or FSBRACKHDP just keep in mind, the original Allan Nimmo Extreme Performance brand rack & pinions were 3/4"-36 spline not 48 spline.

Estimate Shipping

City:
State:
Province:
Postal Code:
Country:
Residential?

Price: $429.99

Call or email for availability

Sold As: 1 Rack and Pinion

Part Number: KTKAABRHDPXTM

OUT OF STOCK

California Prop 65 Warning: This item may cause cancer or reproductive harm. For more info visit p65warnings.ca.gov

Description

If you're replacing an old Allan Nimmo's Extreme Performance brand rack & pinion you'll need to change you're u-joint at the rack because Extreme Performance uses 3/4" 36 spline. Our billet 6061 aluminum fully polished center load steering rack and pinion for Allan Nimmo's Extreme Performance or other A-arm front steer sand rails.

Specs:

American Made
Fully Rebuildable
3/4" 48 Spline Pinion
Depth: 2-1/4" (not including pinion or heim spreader)
Width: 12-9/16"
Travel: 4"
Standard 6" x 1" mounting pattern
Uses 3/8" bolts and nuts
Tie Rod Mounting Holes: 5/8"-18 fine thread
Tie Rod Mounting Hole Width: 5-7/8" on center
Uses KMX1210, RSMX10T, XAM10T, or RXAM-10T heim joints
Tie rods must be in FRONT of spindles

Kartek Offroad 1.5:1 Ratio Rack And Pinion With 5-7/8" Bump Steer Bracket For Extreme Performance

OUT OF STOCK

Description

Related Parts

Billet Bump Steer Tie Rod Mounting Bracket For Our Center Load Rack And Pinions 1-3/4" To 5-7/8"

Kartek Offroad 1.5:1 Ratio Hard Anodized Center Load Rack And Pinion For A-Arm Sand Cars

Kartek Offroad 1.5:1 Ratio Polished Center Load Rack And Pinion For A-Arm Sand Cars

Kartek Offroad 1.5:1 Ratio Rack And Pinion With 11" Bump Steer Brkt For Desert Dynamics Buggy Works

FK Rod Ends 3/4" Right Hand Thread 5/8" Hole KMX12-10 Nylon Coated Heim Joints

FK Rod Ends 3/4" Right Hand Thread 5/8" Hole RSMX10T PTFE Coated Chromoly Heim Joints F2 Fit

Aurora Bearing Company 3/4" Right Hand Thread 5/8" Hole XAM-10T PTFE Coated Chromoly Heim Joints

Aurora Bearing Company 3/4" Right Hand Thread 5/8" Hole RXAM-10T PTFE Coated Chromoly Heim Joints

Kartek Off-Road Custom Made 4130 Chromoly Tie Rods For 3/4" Heim Joints And Rod Ends On Both Sides

Kartek Off-Road HD Custom Made 4130 Chromoly Tie Rods For 3/4" Heim Joints And Rod Ends On Both Side

Steering Coupler 3/4 Smooth Steering Shaft To 3/4-36 Spline Rack And Pinion

Steering Universal Joint 3/4 Smooth To 3/4-36 Spline Steering Shaft Or Rack And Pinion

Double Steering Universal Joint 3/4 Smooth To 3/4-36 Spline Steering Shaft Or Rack And Pinion

Steering Shaft 4130 Chromoly Steel Round Tubing 3/4" Outside Dia 0.120" Wall 0.510" Inside Dia 8Ft L

Grade 9 Fine Thread 5/8"-18 Hex Bolt 1-1/2" Long f911 Foremost Threaded, PFC9 Porteous Fasteners, L9

Replacement Boss For Our Front Steer Center Load Rack And Pinions 1/2" Bolt Holes 1-3/4" On Center

Replacement Rack And Pinion Bronze Support Bushing For The Pinion 5/8" OD x 1/2" ID x 1/2" Long

Replacement 6004RS Rack And Pinion Sealed Support Bearing For The Pinion 42mm OD x 20mm ID x 12mm

Replacement 10 Tooth 3/4" 48 Spline Pinion Gear For Our Center Load And End Load Rack And Pinions

Kartek Offroad 1.5:1 Ratio Rack And Pinion With 5-7/8" Bump Steer Bracket For Extreme Performance

Rough Shipping Estimate

OUT OF STOCK

Description

Related Parts